Call Today

 

What're your thoughts on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?

Mounting a bathtub isn't exactly rocket science, yet it does need strong plumbing, woodworking, and in some cases, tiling skills. Replacing an old bathtub with a new one is also a reasonably tough task. If the old bathtub is conveniently accessible, the project can move immediately; if you have to open a wall to get rid of the old bathtub and place the brand-new bathtub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will need an assistant to leave the old bathtub and also embeded in the brand-new one. Make sure you have qualified on your own for the work and also fit trying it. As opposed to hiring a professional to take control of a halfway-completed job, it is much better to think about employing one prior to you start. Opportunities are you may need an expert plumber to make tube connections.
This short article will certainly help you set up a new bath tub in your washroom if you have actually already acquired a brand-new bathtub and don't require to transform the setup of your previous water supply pipelines.
Your devices as well as material checklist need to comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Preparing for the Setup

Firstly, the supporting framework provided with the bath ought to be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to stop strain on the tub.
Fit the adaptable tap connectors to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should now be ready to be fitted in its last position.

 

 

Removing Old Touches

If you require to change old faucets with new ones as a part of your installment, then the first thing you ought to do is separate the supply of water. After doing so, turn on the taps to drain any type of water continuing to be in the system. The process of removing the existing taps can be rather troublesome as a result of the limited gain access to that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have been eliminated, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming during this process. Once the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Before proceeding to fit the new taps, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.

 

 

Mounting the Bathtub

Utilizing the two wooden boards under its feet, put the tub in the called for placement. The wood boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the tub until the level reviews level.
To mount taps, fit all-time low of the furthest adaptable faucet connector to the suitable supply pipe by making a compression sign up with; after that do the same for the other faucet.
Turn on the water and also check all joints and brand-new pipework for leakages and also tighten them if needed. Fill the bathtub and likewise examine the overflow electrical outlet as well as the regular electrical outlet for leaks.
Finally, deal with the bath paneling as described in the producer's instruction manual. Tiling and securing around the bath tub must wait up until the bathtub has actually been utilized a minimum of once as this will certainly settle it into its last setting.

 

 

Fitting New Touches

If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will need minimizing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin making certain that the washers remain in location in between the tap as well as the sink. Secure the tap in place with the manufacturer offered backnut. Once the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap adapters. The previous type should be attached to the tap finishes initially, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Bathtub

In the location where the bath satisfies the tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to split a rigid seal, triggering the water to penetrate the wall in between the bathroom as well as the tiling, causing problems with dampness and also possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and cartridges, and are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to securing, to allow for the activity experienced when the bathtub is in usage. The sealant can crack rather early if you do not consider this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also easily available on the marketplace. It is suggested to fit the ceramic tiles using water-resistant or waterproof glue as well as cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I'm very involved in How to Install a Bathtub Yourself and I hope you enjoyed my blog posting. For those who appreciated our blog posting kindly don't forget to pass it around. Thank-you for your time invested reading it.

24/7 emergency? We're here!